|Toftejorg MultiJet 25 Rotary Jet Head|
The Toftejorg MultiJet 25 rotary jet head provides 360° indexed impact cleaning over a defined time period. It is ideal for applications where cost-effective impact cleaning with rotary jet heads is needed, but where compliance with hygienic design standards is not a requirement. The device is suitable for process, storage and transportation tanks between 15 and 150 m3 (4,000 to 40,000 US gallons). It is designed to work under conditions where finer particles, etc. in the cleaning media may be re-circulated through the machine.
Sizing/selection and installation drawing are available in Alfa Laval CAS tool for Tank cleaning equipment.
The flow of the cleaning fluid makes the nozzles perform a geared rotation around the vertical and horizontal axes. In the first cycle, the nozzles lay out a coarse pattern on the tank surface. The subsequent cycles gradually make the pattern more dense, until a full pattern is reached after 8 cycles.
|First cycle||Full pattern|
The above drawings show the cleaning pattern achieved on a cylindrical horizontal vessel. The difference between the first cycle and the full pattern represents the number of additional cycles available to increase the density of the cleaning.
The choice of nozzle diameters can optimise jet impact length and flow rate at the desired pressure. The Toftejorg MultiJet 25 is also available with PEEK impeller. A welding adaptor with sealing for 1” ISO, 1” ANSI, 1 1/2” ISO Dairy Pipe or 1 1/2” SWG Pipe is available as an accessory.
ATEX approved, Category 1 for installation in zone 0/20
1.4404 (316L), SAF 2205 (UNS 31803), UNS S 21800, EPDM, PEEK, PVDF, PFA
|Surface finish:||External surface finish: Mat|
|Weight:||5.1 kg (11 lbs)|
|Lubricant:||Self-lubricating with the cleaning fluid|
|Working pressure:||3 - 8 bar (45 - 115 psi)|
|Recommended pressure:||4 - 7 bar (58 - 100 psi)|
|Max. working temperature:||95 °C (203 °F)|
|Max. ambient temperature:||140 °C (284 °F)|
|Max throw length:||9 - 14 m (29 - 46 ft)|
|Impact throw length:||4 - 8 m (13 - 26 ft)|
|Standard thread:||1” Rp (BSP) or NPT, female Top cone|
2.1 - ATEX
Avoid hard and abrasive particles in the cleaning liquid, as this can cause increased wear and/or damage of internal mechanisms. In general, a filter in the supply line is recommended. Do not use for gas evacuation or air dispersion.
Impact Throw Length
Cleaning Time, Complete Pattern
Please specify nozzle size and required connections and confirm application suitability
- - Electronic rotation sensor to verify 360° coverage
- - Downpipes
- - Retractable system
TRAX simulation tool
TRAX is a unique software that simulates how the Toftejorg MultiJet 25 performs in a specific tank or vessel. The simulation gives information on wetting intensity, pattern mesh width and cleaning jet velocity. This information is used to determine the best location of the tank cleaning machine and the correct combination of flow, time and pressure to implement.
A TRAX demo containing different cleaning simulations covering a variety of applications can be used as reference and documentation for tank cleaning applications. The TRAX demo is free and available upon request.
| ||D4.6m H5.5m, Toftejorg MultiJet 25, 4 x 5.5 mm |
Time = 2.08 min., Water consumption = 403 l (106 gallon)
|D4.6m H5.5m, Toftejorg MultiJet 25, 4 x 5.5 mm|
Time = 8.3 min., Water consumption = 1612 l (426 gallon)